Emission factor from ÖKOBAUDAT OBD_2024_III EPD, product-specific

MAGNA3 50-40/60/80/100/120 F (Stainless Steel) and MAGNA3 32-120 F (Stainless Steel)

Germany · EPD total · Reference year 2024

Each unit of this product counts as 229 kg CO₂e over the modules its EPD declares: 108 in use (B6) and 121 for cradle to grave, embodied.

Value per unit, module B6 only

229kgCO₂e/unit

EN 15804 module B6 · Fossil only · GWP100 · AR5

FossilBio CH₄Land useBio CO₂EN 15804 GWP-fossil

Derived by open-climate.ai: the sum of ÖKOBAUDAT's published parts

The one scenario this EPD declaresReference year 2024

Region
Germany DE
Boundary
EPD total
Data quality
HighRated by us, not by the source
Licence
Open · ÖKOBAUDAT terms
Declared by
Grundfos Holding A/S

Where 229 comes from

Derived by open-climate.ai

Σ 229: the two declared modules add up to the total. D stays beside it.

Reporting this item under the GHG Protocol

This period

Scope 3, categories 2 and 4 121

This one figure covers both together; no split between them is given.

The product becomes part of a building you own. The product and its installation go to category 2 in the year you buy it, the delivery to category 4. Use and end of life are reported in the years they happen.

Later, when it happens

During use, in the years the building stands

  • B6 Scope 1 Scope 2 3.3 Energy upstream 108

At end of life, in the year of demolition

  • Cradle to grave, embodied 3.5 Waste 121

Outside the scopes, reported separately

  • D −8.57

A1-A3 to A5, B1 to B5, B7 and C1 to C4 are not declared: nothing to report.

CiteAPI

The factor, standardised

Every factor on open-climate.ai answers the same questions in the same words, whatever the publisher. Open any ⓘ for the definition.

Manufactured goods › Machinery · Germany · per item · Supplier-specific

EPD total · Fossil only · AR5

Boundary
EPD total
Raw materials, inbound transport, fuel supply, fuel combustion, manufacturing, packaging, purchased energy, installation, outbound transport, use, maintenance and end of life
GWP method
IPCC AR5, 100-year horizon
Not on the record; set from ÖKOBAUDAT's method notes · impact method EF 3.0
CO₂e basis
Fossil onlyFossilBio CH₄Land useBio CO₂EN 15804 GWP-fossil
Split by carbon origin, not by gas
Life cycle
Upstream: coveredProduction: coveredDownstream: partly coveredEnd of life: partly covered

High quality · Open licence · Any year

Module by module, up to the total

Seventeen EN 15804 modules, always in the same order. Each declared one moves the running total. D sits below zero after the total, because it is reported beside it.

kgCO₂e per unit. Each bar starts where the one before ended. Pick a module to read it.
Product
Con­struc­tion
Use
B1 to B5not de­clared
B7not de­clared
End of life
C1not de­clared
Beyond the boundary

beside the total, not in it

What this number covers

Follow 1 unit of this product through EN 15804's stages. The total counts what the EPD declares; what it leaves out stays visible.

  1. A1-A3Product

    Materials and making the product

    Included113
  2. A4-A5Construction

    Delivery and installation

    Included1.69
  3. B1-B7Use

    Energy in use only; B1 to B5, B7 not declared

    B6 only108
  4. C1-C4End of life

    Waste transport to disposal; C1 not declared

    C2 to C46.49
  5. DBeyond the boundary

    Recovery after end of life

    Not in the total−8.57

Outside this boundary

  • Retail
  • Recycling credit

The recycling credit is module D, shown beside the total.

Gases

  • Fossil CO₂e229
  • Biogenic CO₂e0.553
  • Land-use CO₂e0.133

The total counts fossil CO₂e. ÖKOBAUDAT reports biogenic and land-use CO₂e separately; they are shown beside it, not added.

From ÖKOBAUDAT's record to a comparable factor

ÖKOBAUDAT publishes this EPD as one declared value. Each field as printed, and what open-climate.ai made of it.

The total and its modules

Use a module on its own when you report it in a different year or scope; never add one to the total.

You are here · the EPD total229
D beside−8.57
The two modules add up to the total; D stays beside it. Each opens its own page.

About this factor

From ÖKOBAUDAT

What it is

The Grundfos MAGNA3 circulator pumps are designed for circulating liquids in heating systems, air conditioning and cooling systems and domestic hot water systems. However, the pump range can also be used in ground source heat pump systems and solar heating systems. The MAGNA3 pump is a centrifugal pump powered by an electrical motor. It has a high-performance neodymium magnet rotor which increases motor efficiency and an insulation shell to reduce heat loss from the cast iron pump housing with threaded connections. The declaration covers six types of the MAGNA3 pump. They are listed below. The group reference in the technical data and scenarios refers also to these. MAGNA3 50-40 F (Group 1) MAGNA3 50-60 F (Group 2) MAGNA3 50-80 F (Group 3) MAGNA3 50-100 F (Group 4) MAGNA3 50-120 F (Group 5) MAGNA3 32-120 F (Group 6) The MAGNA 3 50-40/60/80/100/120 F are all the same physical products and 100 % identical in terms of design, dimensions and materials as well as supply chain and manufacturing processes, i.e., all cradle to gate processes (A1-A3).The MAGNA 3 32-120 flanged version (F), although smaller, utilizes the same technology and materials as the MAGNA 3 50-40/60/80/100/120 F. Given its smaller size, it is expected to have a lower environmental impact in A1-A3, but the MAGNA 3 50-40/60/80/100/120 F results will cover it being the 'worst-case' scenario EPD of the MAGNA3 32-120 F. The justification is the reduced material usage and the lower energy consumption during operation. The technical specifications table is separate for the 32-120 F, which clearly proves the justification. The B6 factor will also be indicated. The products are also identical in terms of packaging, distribution, reference service life and end-of-life treatment. The only thing that differentiates the products from each other is the software which controls how the pump operates in the system in which it is installed, making them fit for different applications. Hence, all life cycle modules are identical, except use stage module B6, which will change, as the applied scenarios for electricity consumption changes.

What it includes

The Grundfos MAGNA3 circulation pumps are designed for circulating liquids in heating systems, air conditioning and cooling systems and domestic hot water systems. However, the pump series can also be used in geothermal heat pump systems and solar systems. Technical data: The performance data of the product according to the harmonised norms, based on the harmonisation provisions above apply. The relevant technical specifications according to the PCR Part B are given in the table below. Characteristics that are the same for all three product groups are only given once. Others are given individually for all three groups. Declared unit: The declared unit is 1 piece (pcs.) of MAGNA3 Stainless Steel pump.

Where it applies

For the application and use the respective national provisions apply. The pump is designed for circulating liquids in the following systems: · heating systems · domestic hot-water systems · air-conditioning and cooling systems · ground-source heat-pump systems · solar-heating systems The pump is suitable for thin, clean, non-aggressive and non-explosive liquids, not containing solid particles or fibres that may attack the pump mechanically or chemically. In heating systems, the water must meet the requirements of accepted standards on water quality. The pumps are also suitable for domestic hot-water systems.

Source and licence

Value
Summed by open-climate.ai from its parts
Publisher
ÖKOBAUDAT (BBSR / BMWSB)
Published
13 November 2026
Valid until
31 December 2029
See the source data at ÖKOBAUDAT

The values and their metadata are served in full and may be reused with credit to the publisher.

Credit it with this lineSource: ÖKOBAUDAT (OBD_2024_III), BBSR / BMWSB. Individual EPDs © their respective programme operators / declaration owners.
A plain reading of the licence, not legal advice. The licence text prevails.

Cite this factor

Source: ÖKOBAUDAT (OBD_2024_III), BBSR / BMWSB. Individual EPDs © their respective programme operators / declaration owners. Normalised by open-climate.ai, https://open-climate.ai/factors/libraries/okobaudat/ (CC BY 4.0). https://open-climate.ai/factors/ef-okobaudat-magna3_50406080100120_f-de-unit-epd_total-9e72ea26/?v=efv1-29466fab7d5969047bb9169f3d8498d3

Something looks wrong?

Tell us which value and why. We check it against the source and answer within a week.

Page data as of .