Emission factor from ÖKOBAUDAT OBD_2024_III EPD, industry average

Rubner Sawn Timber, Rubner Sawn Timber kiln dried, Rubner Sawn Timber machine graded

Austria · EPD total · Reference year 2023

Each litre of this product counts as 0.0332 kg CO₂e over the modules its EPD declares: 0.0285 to make it (A1–A3) and 0.00477 at end of life.

Value per litre, over the modules the EPD declares

0.0332kgCO₂e/L

EN 15804 modules A1 to A3 · Fossil only · GWP100 · AR5

FossilBio CH₄Land useBio CO₂EN 15804 GWP-fossil

Derived by open-climate.ai: the sum of ÖKOBAUDAT's published parts

The one scenario this EPD declaresReference year 2023

Region
Austria AT
Boundary
EPD total
Data quality
MediumRated by us, not by the source
Licence
Open · ÖKOBAUDAT terms
Declared by
Rubner Holding AG - S.p.A.
Declared unit
Served per litre ÷ 1,000

Where 0.0332 comes from

Derived by open-climate.ai

Σ 0.0332: the two declared modules add up to the total. D stays beside it.

Reporting this litre under the GHG Protocol

This period

3.1 Goods we buy 0.0285

You buy the product for a building that is not yours. The product and its installation go to category 1, the delivery to category 4. The use stage belongs to the building owner; demolition waste you handle is category 5.

Later, when it happens

At end of life, in the year of demolition

  • End of life 3.5 Waste 0.00477

Outside the scopes, reported separately

  • D −0.381

A4, A5, B1 to B7 and C1 to C4 are not declared: nothing to report.

CiteAPI

The factor, standardised

Every factor on open-climate.ai answers the same questions in the same words, whatever the publisher. Open any ⓘ for the definition.

Materials › Paper and wood · Austria · per L · Average

EPD total · Fossil only · AR5

Boundary
EPD total
Raw materials, inbound transport, fuel supply, fuel combustion, manufacturing, packaging, purchased energy and end of life
GWP method
IPCC AR5, 100-year horizon
Not on the record; set from ÖKOBAUDAT's method notes · impact method EF 3.0
CO₂e basis
Fossil onlyFossilBio CH₄Land useBio CO₂EN 15804 GWP-fossil
Split by carbon origin, not by gas
Life cycle
Upstream: coveredProduction: coveredDownstream: not coveredEnd of life: partly covered

Medium quality · Open licence · Any year

Module by module, up to the total

Seventeen EN 15804 modules, always in the same order. Each declared one moves the running total. D sits below zero after the total, because it is reported beside it.

kgCO₂e per litre. Each bar starts where the one before ended. Pick a module to read it.
Product
Con­struc­tion
A4 to A5not de­clared
Use
B1 to B7not de­clared
End of life
C1not de­clared
C4not de­clared
Beyond the boundary

beside the total, not in it

Scenarios and units

Some EPDs price a module under several scenarios, such as different end-of-life routes. Each gets a tab, and each module's default is marked.

This factor

One scenario, as declared

Every module has one value, so there is nothing to choose.

  • Per m³, as declared33.2309
  • Per litre, served0.0332309

What this number covers

Follow one litre of this product through EN 15804's stages. The total counts what the EPD declares; what it leaves out stays visible.

  1. A1-A3Product

    Materials and making the product

    Included0.0285
  2. A4-A5Construction

    Delivery and installation

    Not declared
  3. B1-B7Use

    The product in service: maintenance, repair, replacement and the energy and water it uses

    Not declared
  4. C1-C4End of life

    Waste transport and waste processing; C1, C4 not declared

    C2, C30.00477
  5. DBeyond the boundary

    Recovery after end of life

    Not in the total−0.381

Outside this boundary

  • Installation
  • Maintenance
  • Outbound transport
  • Retail
  • Use phase
  • Recycling credit

Maintenance is out because B2 is not declared. The recycling credit is module D, shown beside the total.

Gases

  • Fossil CO₂e0.0332
  • Biogenic CO₂e0.00223
  • Land-use CO₂e0.000146

The total counts fossil CO₂e. ÖKOBAUDAT reports biogenic and land-use CO₂e separately; they are shown beside it, not added.

From ÖKOBAUDAT's record to a comparable factor

ÖKOBAUDAT publishes this EPD as one declared value. Each field as printed, and what open-climate.ai made of it.

The total and its modules

Use a module on its own when you report it in a different year or scope; never add one to the total.

You are here · the EPD total0.0332
D beside−0.381
The two modules add up to the total; D stays beside it. Each opens its own page.

About this factor

From ÖKOBAUDAT

What it is

RUBNER sawn timber is produced from fresh roundwood, whereby the wood species spruce and pine are processed in accordance with EN 1912 (Picea abies and Pinus sylvestris). The roundwood for the production of RUBNER sawnwood originates from a predominantly regional supply network, the average delivery distance of the roundwood is around 80 km. Depending on the processing level, RUBNER sawn timber is available as fresh, dried, dried/pre-planed or dried/planed/(visually) machine-graded lath, board or plank sawn timber.

What it includes

RUBNER sawn timber is manufactured from sustainable wood (PEFC) sourcing from sustainable forestry. After delivery to the production facility, a quality and volume assessment is carried out. After debarking, the logs are classified according to their diameter and temporarily stored at the log yard (dry & wet storage). In the sawing line, the logs are split into main and side boards with circular saws and then (side boards) prismatically edged. RUBNER sawn timber that is not dried is then visually graded and packaged. Dried RUBNER sawn timber is kiln dried after the sawing process, with a target moisture content between 10 and 18 percent. RUBNER sawn timber graded according to strength is pre-planed after technical drying and then visually or mechanically graded by strength. Optionally, the kiln-dried Rubner sawn timber is protected from the weather during intermediate storage and transport with foils. Technical data: RUBNER sawn timber has the mechanical properties required for use in timber structures according to EN 1995 (all parts). The following technical data apply to the properties of RUBNER sawn timber. The performance data of the product are in accordance with its essential characteristics according to EN 14081. Declared unit: This EPD refers to a declared unit of 1 m³ of sawn timber produced by the RUBNER group. The declared unit refers to an average density of 459 kg/m³ and wood moisture at delivery of 12 %.
Show ÖKOBAUDAT's original (German)
RUBNER Schnittholz wird aus nachhaltigem Holz (PEFC) hergestellt, das aus nachhaltiger Forstwirtschaft stammt. Nach der Anlieferung in der Produktionsstätte wird eine Qualitäts- und Mengenbeurteilung durchgeführt. Nach der Entrindung werden die Stämme nach ihrem Durchmesser klassifiziert und auf dem Rundholzplatz zwischengelagert (Trocken- und Nasslager). In der Sägelinie werden die Stämme mit Kreissägen in Haupt- und Seitenbretter gespalten und anschließend (Seitenbretter) prismatisch besäumt. Nicht getrocknetes RUBNER Schnittholz wird anschließend visuell sortiert und verpackt. Getrocknetes RUBNER Schnittholz wird nach dem Sägen in der Trockenkammer getrocknet, mit einer Zielfeuchte zwischen 10 und 18 Prozent. Nach der Festigkeit sortiertes RUBNER Schnittholz wird nach der technischen Trocknung vorgehobelt und anschließend visuell oder maschinell nach der Festigkeit sortiert. Optional wird das kammergetrocknete Rubner Schnittholz bei der Zwischenlagerung und beim Transport mit Folien vor Witterungseinflüssen geschützt. Technische Daten: RUBNER Schnittholz besitzt die für den Einsatz im Holzbau erforderlichen mechanischen Eigenschaften gemäß EN 1995 (alle Teile). Die folgenden technischen Daten gelten für die Eigenschaften von RUBNER Schnittholz. Die Leistungsdaten des Produkts entsprechen den wesentlichen Eigenschaften gemäß EN 14081. Deklarierte Einheit: Diese EPD bezieht sich auf eine deklarierte Einheit von 1 m³ Schnittholz, das von der RUBNER-Gruppe produziert wird. Die deklarierte Einheit bezieht sich auf eine durchschnittliche Dichte von 459 kg/m³ und eine Holzfeuchte bei Lieferung von 12 %.

Where it applies

RUBNER sawn timber classified according to purely visual criteria is used in the construction sector for both decorative and structural purposes. RUBNER sawn timber graded according to its strength can be used for the construction of load-bearing components in buildings and bridges. RUBNER sawn timber graded according to its strength is mainly used as a base material for various wood-based materials such as glulam, cross-laminated timber or finger-jointed solid structural timber.

Source and licence

Value
Summed by open-climate.ai from its parts
Publisher
ÖKOBAUDAT (BBSR / BMWSB)
Published
13 November 2026
Valid until
31 December 2028
See the source data at ÖKOBAUDAT

The values and their metadata are served in full and may be reused with credit to the publisher.

Credit it with this lineSource: ÖKOBAUDAT (OBD_2024_III), BBSR / BMWSB. Individual EPDs © their respective programme operators / declaration owners.
The publisher's text on this page is translated by open-climate.ai.A plain reading of the licence, not legal advice. The licence text prevails.

Cite this factor

Source: ÖKOBAUDAT (OBD_2024_III), BBSR / BMWSB. Individual EPDs © their respective programme operators / declaration owners. Normalised by open-climate.ai, https://open-climate.ai/factors/libraries/okobaudat/ (CC BY 4.0). https://open-climate.ai/factors/ef-okobaudat-rubner_sawn_timber-at-l-epd_total-d00e9e25/?v=efv1-d0e94e8406cde4bcb0d23e0326b4da7d

Something looks wrong?

Tell us which value and why. We check it against the source and answer within a week.

Page data as of .