Emission factor from ÖKOBAUDAT OBD_2024_III EPD, industry average

TPE2, TPE3 40-80_120_150_180 (Cast iron)

Europe · EPD total · Reference year 2025

Each unit of this product counts as 4,125 kg CO₂e over the modules its EPD declares: 4,013 in use (B6) and 112 for cradle to grave, embodied.

Value per unit, module B6 only

4,125kgCO₂e/unit

EN 15804 module B6 · Fossil only · GWP100 · AR6

FossilBio CH₄Land useBio CO₂EN 15804 GWP-fossil

Derived by open-climate.ai: the sum of ÖKOBAUDAT's published parts

The one scenario this EPD declaresReference year 2025

Region
Europe
Boundary
EPD total
Data quality
MediumRated by us, not by the source
Licence
Open · ÖKOBAUDAT terms
Declared by
Grundfos Holding A/S

Where 4,125 comes from

Derived by open-climate.ai

Σ 4,125: the two declared modules add up to the total. D stays beside it.

Reporting this item under the GHG Protocol

This period

Scope 3, categories 2 and 4 112

This one figure covers both together; no split between them is given.

The product becomes part of a building you own. The product and its installation go to category 2 in the year you buy it, the delivery to category 4. Use and end of life are reported in the years they happen.

Later, when it happens

During use, in the years the building stands

  • B6 Scope 1 Scope 2 3.3 Energy upstream 4,013

At end of life, in the year of demolition

  • Cradle to grave, embodied 3.5 Waste 112

Outside the scopes, reported separately

  • D −14.2

A1-A3 to A5, B1 to B5, B7 and C1 to C4 are not declared: nothing to report.

CiteAPI

The factor, standardised

Every factor on open-climate.ai answers the same questions in the same words, whatever the publisher. Open any ⓘ for the definition.

Manufactured goods › Machinery · Europe · per item · Average

EPD total · Fossil only · AR6

Boundary
EPD total
Raw materials, inbound transport, fuel supply, fuel combustion, manufacturing, packaging, purchased energy, installation, outbound transport, use, maintenance and end of life
GWP method
IPCC AR6, 100-year horizon
Not on the record; set from ÖKOBAUDAT's method notes · impact method EF 3.1
CO₂e basis
Fossil onlyFossilBio CH₄Land useBio CO₂EN 15804 GWP-fossil
Split by carbon origin, not by gas
Life cycle
Upstream: coveredProduction: coveredDownstream: partly coveredEnd of life: partly covered

Medium quality · Open licence · Any year

Module by module, up to the total

Seventeen EN 15804 modules, always in the same order. Each declared one moves the running total. D sits below zero after the total, because it is reported beside it.

kgCO₂e per unit. Each bar starts where the one before ended. Pick a module to read it.
Product
Con­struc­tion
Use
B1 to B5not de­clared
B7not de­clared
End of life
C1not de­clared
Beyond the boundary

beside the total, not in it

What this number covers

Follow 1 unit of this product through EN 15804's stages. The total counts what the EPD declares; what it leaves out stays visible.

  1. A1-A3Product

    Materials and making the product

    Included102
  2. A4-A5Construction

    Delivery and installation

    Included5.52
  3. B1-B7Use

    Energy in use only; B1 to B5, B7 not declared

    B6 only4,013
  4. C1-C4End of life

    Waste transport to disposal; C1 not declared

    C2 to C44.56
  5. DBeyond the boundary

    Recovery after end of life

    Not in the total−14.2

Outside this boundary

  • Retail
  • Recycling credit

The recycling credit is module D, shown beside the total.

Gases

  • Fossil CO₂e4,125
  • Biogenic CO₂e36.1
  • Land-use CO₂e0.841

The total counts fossil CO₂e. ÖKOBAUDAT reports biogenic and land-use CO₂e separately; they are shown beside it, not added.

From ÖKOBAUDAT's record to a comparable factor

ÖKOBAUDAT publishes this EPD as one declared value. Each field as printed, and what open-climate.ai made of it.

The total and its modules

Use a module on its own when you report it in a different year or scope; never add one to the total.

You are here · the EPD total4,125
D beside−14.2
The two modules add up to the total; D stays beside it. Each opens its own page.

About this factor

From ÖKOBAUDAT

What it is

TPE2 and TPE3 (TPE2/3) pumps are single-stage, in-line centrifugal pumps mounted with electronically speed-controlled MGE motors (motor efficiency class IE5). The pumps are designed for systems with variable flow rates. The pumps have integrated speed control for automatic adaptation of performance to the varying flow conditions. The energy consumption is thus kept at a minimum. This declaration covers all standard Cast iron TPE2 and TPE3 pump variants with the nominal connection size 40 and maximum head 80, 120, 150, or 180 dm: 1. TPE2 40-80, TPE3 40-80; 2. TPE2 40-120, TPE3 40-120; 3. TPE2 40-150, TPE3 40-150; 4. TPE2 40-180, TPE3 40-180. These pump models (1-4) were treated together as they physically represent very similar products in terms of materials, weights, and contents of electronics. A representative pump model (4) was applied for assessing the impacts of the A, C, and D stages. However, for the B stage, the individual impacts related to motor variations delivering the prescribed head were considered. This entails impact reduction factors to be applied for B6, as outlined in the Results section. TPE2/3 is an electronic product and is installed as part of the service functions of buildings and systems. It does however not apply to the Construction Products Regulation (CPR) in requiring any Declaration of Performance. For placing the product on the EU/EFTA market, a CE-marking is required. According to its Declaration of Conformity, TPE2/3 is in conformity with the following Council Directives: Machinery Directives (2006/42/EC and 2009/127/EC) Radio Equipment Directive (2014/53/EU) RoHS Directives (2011/65/EU and 2015/863/EU) EMC Directive (2014/30/EU) The CE-marking takes into account the proof of conformity with the respective harmonized standards based on the legal provisions above. For the application and use the respective national provisions apply.

What it includes

TPE2 and TPE3 (TPE2/3) pumps are single-stage, in-line centrifugal pumps mounted with electronically speed-controlled MGE motors (motor efficiency class IE5). The pumps are designed for systems with variable flow rates. The pumps have integrated speed control for automatic adaptation of performance to the varying flow conditions. The energy consumption is thus kept at a minimum. Technical data: The declared unit is represented by the pump variant whose technical data is provided in the Pump technical data table. Declared unit: The declared unit is a representative TPE2/3 40-80/120/150/180 (Cast iron) pump variant whose mass including packaging is provided in the table.

Where it applies

TPE2 and TPE3 pumps are applied in systems with variable flow rates. Other applications are in district water supply and industrial processes.

Source and licence

Value
Summed by open-climate.ai from its parts
Publisher
ÖKOBAUDAT (BBSR / BMWSB)
Published
13 November 2026
Valid until
31 December 2030
See the source data at ÖKOBAUDAT

The values and their metadata are served in full and may be reused with credit to the publisher.

Credit it with this lineSource: ÖKOBAUDAT (OBD_2024_III), BBSR / BMWSB. Individual EPDs © their respective programme operators / declaration owners.
A plain reading of the licence, not legal advice. The licence text prevails.

Cite this factor

Source: ÖKOBAUDAT (OBD_2024_III), BBSR / BMWSB. Individual EPDs © their respective programme operators / declaration owners. Normalised by open-climate.ai, https://open-climate.ai/factors/libraries/okobaudat/ (CC BY 4.0). https://open-climate.ai/factors/ef-okobaudat-tpe2_tpe3_4080120150180-europe-unit-epd_total-dac1a235/?v=efv1-a18c86ca5a09dd2d3aed493d4701f3d4

Something looks wrong?

Tell us which value and why. We check it against the source and answer within a week.

Page data as of .