open-climate.aiFactors

Emission factor from EPD Italy EPD, product-specific

Painted Aluminium Coil (0.46-3003)

China · EPD total · Reference year 2025

Each kilogram of this product counts as 16.2 kg CO₂e over the modules its EPD declares: 14.9 to make it (A1–A3) and 1.24 at end of life.

Value per kilogram, over the modules the EPD declares

16.2kgCO₂e/kg

EN 15804 modules A1 to A3 · Fossil only · GWP100 · AR5

Derived by open-climate.ai: the sum of EPD Italy's published parts

The one scenario this EPD declaresReference year 2025

Region
China CN
Boundary
EPD total
Data quality
HighRated by us, not by the source
Licence
Open · EPD Italy terms
Declared by
Jiangsu Lidao New Material Co., LTD.

Where 16.2 comes from

Derived by open-climate.ai

Σ 16.2: the two declared modules add up to the total. D stays beside it.

Reporting this kilogram under the GHG Protocol

This period

Scope 3, category 1 14.9

You buy the product for a building that is not yours. The product and its installation go to category 1, the delivery to category 4. The use stage belongs to the building owner; demolition waste you handle is category 5.

Later, when it happens

At end of life, in the year of demolition

  • End of life Scope 3, category 5 1.24

Outside the scopes, reported separately

  • D −4.52

A4, A5, B1 to B7 and C1 to C4 are not declared: nothing to report.

CiteAPI

The factor, standardised

Every factor on open-climate.ai answers the same questions in the same words, whatever the publisher. Open any ⓘ for the definition.

Materials › Metals · China · per kg · Supplier-specific

EPD total · Fossil only · AR5

Boundary
EPD total
Raw materials, inbound transport, fuel supply, fuel combustion, manufacturing, packaging, purchased energy and end of life
GWP method
IPCC AR5, 100-year horizon
Not on the record; set from EPD Italy's method notes · impact method EF 3.0
CO₂e basis
Fossil only
Split by carbon origin, not by gas
Life cycle
Upstream: coveredProduction: coveredDownstream: not coveredEnd of life: partly covered

High quality · Open licence · Any year

Module by module, up to the total

Seventeen EN 15804 modules, always in the same order. Each declared one moves the running total. D sits below zero after the total, because it is reported beside it.

kgCO₂e per kilogram. Each bar starts where the one before ended. Pick a module to read it.
Product
Con­struc­tion
A4 to A5not de­clared
Use
B1 to B7not de­clared
End of life
Beyond the boundary

beside the total, not in it

What this number covers

Follow one kilogram of this product through EN 15804's stages. The total counts what the EPD declares; what it leaves out stays visible.

  1. A1-A3Product

    Materials and making the product

    Included14.9

  2. A4-A5Construction

    Delivery and installation

    Not declared

  3. B1-B7Use

    The product in service: maintenance, repair, replacement and the energy and water it uses

    Not declared

  4. C1-C4End of life

    From demolition to disposal

    Included1.24

  5. DBeyond the boundary

    Recovery after end of life

    Not in the total−4.52

Outside this boundary

  • Installation
  • Maintenance
  • Outbound transport
  • Retail
  • Use phase
  • Recycling credit

Maintenance is out because B2 is not declared. The recycling credit is module D, shown beside the total.

Gases

  • Fossil CO₂e16.2
  • Biogenic CO₂e0.0263
  • Land-use CO₂e0.141

The total counts fossil CO₂e. EPD Italy reports biogenic and land-use CO₂e separately; they are shown beside it, not added.

From EPD Italy's record to a comparable factor

EPD Italy publishes this EPD as one declared value. Each field as printed, and what open-climate.ai made of it.

The total and its modules

Use a module on its own when you report it in a different year or scope; never add one to the total.

You are here · the EPD total16.2
D beside−4.52
The two modules add up to the total; D stays beside it. Each opens its own page.

About this factor

From EPD Italy

What it is

1kg product Geographical representativeness and technical representativeness mostly are good, and time representativeness is very good. the physical relationship (yield) is adopted to allocate electricity, photovoltaic power, water, natural gas and diesel. "All inputs and outputs to a (unit) process shall be included in the calculation, for which data are available. Data gaps may be filled by conservative assumptions with average or generic data. Any assumptions for such choices shall be documented; — In case of insufficient input data or data gaps for a unit process, the cut-off criteria shall be 1 % of renewable and non-renewable primary energy usage and 1 % of the total mass input of that unit process. The total of neglected input flows per module, e.g. per module A1-A3, A4-A5, B1-B5, B6-B7, C1-C4 and module D shall be a maximum of 5 % of energy usage and mass. Conservative assumptions in combination with plausibility considerations and expert judgement can be used to demonstrate compliance with these criteria; — Particular care should be taken to include material and energy flows known to have the potential to cause significant emissions into air and water or soil related to the environmental indicators of this standard. Conservative assumptions in combination with plausibility considerations and expert judgement can be used to demonstrate compliance with these criteria.According to the above cut-off principle, this study ignored the environment impact of infrastructure such as roads and factories, production equipment, personnel and living facilities in the plant."

What it includes

Painted Aluminium Coil (3.0-5052) Painted Aluminium Coil (1.5-3003) Painted Aluminium Coil (1.2-3004) Painted Aluminium Coil (0.98-3003) Painted Aluminium Coil (0.9-3004) Painted Aluminium Coil (0.7-5005) Painted Aluminium Coil (0.6-5052) Painted Aluminium Coil (0.46-3003) Painted Aluminium Coil (0.38-3003) Painted Aluminium Coil (1.0-3003)

Where it applies

The Painted Aluminium Coil for Construction is a high - performance material designed for building applications, offering durability, weather - resistance, excellent formation capabilities. Products can be used in industries such as construction, household appliances, and transportation. The technical standards and performance index requirements can be referred to YS/T 431—2009 Aluminium and aluminium alloys—Coil coated sheet and strip. The identification name is determined by the thickness of aluminium coils (cm) and the alloy grade utilized in the product manufacturing process.

Source and licence

Value
Summed by open-climate.ai from its parts
Publisher
EPD Italy (ICMQ)
Library
EPD Italy EPD_ITALY_2026-10-02
Published
2 October 2026
Valid until
31 December 2030
See the source data at EPD Italy
EPD Italy's terms of use Open

The values and their metadata are served in full and may be reused with credit to the publisher.

Credit it with this lineEPD Italy (ICMQ), EPD data from https://epditaly.lca-data.com
A plain reading of the licence, not legal advice. The licence text prevails.

Cite this factor

EPD Italy (ICMQ), EPD data from https://epditaly.lca-data.com. Normalised by open-climate.ai, https://open-climate.ai/factors/libraries/epd_italy/ (CC BY 4.0). https://open-climate.ai/factors/ef-epditaly-painted_aluminium_coil-cn-kg-epd_total-2ea72278/?v=efv1-cdca6254a57b9f1952ccfc5dce79df00

Something looks wrong?

Tell us which value and why. We check it against the source and answer within a week.